Simple correction method for cutter beam of large-sized harvester

Park the harvesting table on the trailer dedicated trailer. When parking, try to make the two ends of the harvesting table bear the supporting force. Do not put the middle U-shaped beam on the girder of the trailer. Check for any breaks, if any, correct them first.
Remove the knife before calibration to prevent the knife from deforming during calibration. It is best to remove the knife completely. One person visually pointed and pointed out the deformation of the beam from the tip of the knife to the end of the blade. The other person took chalk to mark the highest point, the second highest point, and the third highest point. Then, according to the number of marks, a corresponding number of jacks (5 to 8t) and round logs (10 to 15 cm in diameter) are prepared. One end of the log is opened into a V-shaped groove, and the other end is sawed into a plane. The length of the log is determined according to the measured distance during operation. Finally prepare some flat iron or flat wrenches. After the preparation is completed, a jack and a log are slanted between the highest point of the cutter beam and the square beam above the header. One end of the V-groove of the round wood is just above the corner of the square beam, and the plane just sits on top of the jack. The bottom of the jack sits on the corner of the cutter beam. Place the prepared flat iron plate or flat wrench in the angle between the jack and the cutter beam and the header plate so that the jack is stable. The jack rises slowly, causing the knife beam to excessively deform 1 to 2 centimeters. Then, the second highest point and the third highest point are pushed up one after another. After jacking up, park for 1 to 2 hours before loosening the jack. Check whether the cutter beam is straight and if not straight, use the above method to cold press until satisfied. The jacks can be replaced when cold pressure is applied again.
Operation must pay attention to safety, the jack must be stable, the operator must work sideways, beware of jacks outward wounded.

Drostanolone which is also known as [Masteron",they are very popular in bodybuilding. Drostanolone Steroids includes Drostanolone Enanthate and Drostanolone Propionate,they are an anabolic androgenic steroid of the dihydrotestosterone.Their appearance of powder form is white crystalline Raw Steroids powder,it`s just like tiny sugar and salt.We can see them on the market are usually in injection form,Semi-finished oils or finished oils.People use them mostly for losing fat,boosting strength,gain lean muscle in the cycle,treating cancer.They are not a bulking choice and mild even for women.Although Drostanolone contains such anti-estrogenic properties, it also has anabolic and androgenic properties. According to its properties, it may be not a very strong androgen,but in fact Drostanolone does give higher androgenic effects than one may expect,it is different from Bodybuilding Peptides and Sarms Raws .When Drostanolone is used as an AAS, it will shut down natural testosterone production and so despite having anti-estrogenic effects again, so that Drostanolone couldn`t be used as an option in post cycle therapy as it will inhibit recovery.According to research,Drostanolone Propionate will reach peak levels in the body faster than the Drostanolone enanthate. Drostanolone Steroids acts very well in combination with Human Growth Hormone .

Drostanolone Propionate is mostly called as Masteron or Masteron propionate on the market.Drostanolone Propionate is a short esters,so it usually need to be injected every day or every other day.Based on it`s short ester,Drostanolone Propionate usually stack with another shorter ester such as Trenbolone Acetate , testosterone propionate, or Nandrolone Phenylpropionate.The detection time of Drostanolone Propionate is about 8-10 days half life.
As for it`s dosage,generally suggest 50mg/week(4-6 weeks)for female, part of can get 100mg/week.And it is better to use Drostanolone Propionate for women,400-600mg/week(6-12 weeks) for male.
Drostanolone Enanthate is mostly named Drostanolone Enanthate is a long esters,so it can be injected less often, usually once or twice per week.Considering it is a long ester,mostly people stack with Testosterone Enanthate or Testosterone Cypionate , Trenbolone Enanthate , or deca Nandrolone Decanoate .The detection time for Drostanolone Enanthate is 3 weeks with a 3-4 day half life.For male,350mgs/week to 500mgs/week and 100mgs every other day is an effective dosage,and 50-100mg/week for female.

Side effects of Methenolone Steroids include acne,hair loss, body hair growth,LDL ups,HDL downs,change sinificantly,supressing natural test production.For the most common side effect of acne,here is some suggestions:1.Washing face with gentle face wash instead of soap at least a couple times a day.2.Change sheet often and never wear a shirt after you have sweat in it.3.Using over the counter acne cream.

How can DIY Drostanolone enanthate,Drostanolone propionate from Raw steroids into semi finished oils or finished oils?

Drostanolone Propionate 100ml@150mg/ml
15 gram Drostanolone Propionate powders
2ml BA (2%)
20ml BB (20%)
66ml Carrier Oil

Drostanolone Propionate 250ml@100mg/ml
25 gram Drostanolone Propionate powders
5ml BA (2%)
50ml BB (20%)
175m lCarrier Oil

Drostanolone Propionate 1000ml@75mg/ml
75 gram Drostanolone Propionate powders
20ml BA (2%)
200ml BB (20%)
720ml Carrier Oil

Drostanolone Enthanate200ml @250mg/ml 
50 gram Drostanolone Propionate powder
5ml BA (2%) 
50ml BB (20%) 
157.5ml Carrier Oil


Drostanolone Steroids

Drostanolone Steroids,Drostanolone Enanthate,Drostanolone Propionate,Anabolic Steroids Drostanolone

beststeroidraws Co., Ltd , http://www.beststeroidraws.com